One design across the entire kitchen. Every section, seam, edge, and veining layer planned together instead of assembled piece by piece, and approved on a physical sample before the first pour.
The problem this solves
Kitchen countertops rarely fail as one surface. They fail as a collection of decisions that never talked to each other. A perimeter run chosen in one moment, an island that doesn't quite relate to it, a backsplash that fights both, and seams landing wherever the material happened to end.
Slab selection makes this harder than it should be. You're choosing from what a warehouse has in stock, which means the pattern was decided by a quarry, not by your room. If nothing on the rack is right, the answer is usually to pick the least wrong option.
A whole-kitchen pour works the other way around. The design starts with your cabinets, flooring, backsplash, hardware, and light. Then we build the surface to match it. Seams get placed where they make sense. Veining continues where you want continuity and shifts where you want the island to lead.
Best for: Homeowners doing the whole kitchen at once, whether that means resurfacing sound counters, fabricating new substrates for a layout change, or both in the same project.
Who this is for
- You're doing the entire kitchen and want it to read as one decision
- You're remodeling or building and the layout is settled
- Your existing counters are sound and you want a full-room transformation without tear-out
- Your existing counters have failed and you need new substrates built
- You want a color and pattern that doesn't exist on any slab rack
- You want to hold a physical sample in your own kitchen before committing
Conditions we address first
- Unresolved moisture damage or structural failure in the existing substrate
- Layouts still in flux where final measurements aren't settled
- Surfaces where dependable adhesion can't be confirmed, which usually means building a new substrate instead
A kitchen that isn't ready doesn't get scheduled. Pouring over a moving target is how a project becomes a callback.
Resurface, rebuild, or both
Most whole-kitchen projects turn out to be a mix, and that's fine.
Resurfacing in place. Where the existing counters are firmly bonded, dry, and stable, we prepare and pour over them. Less demolition, less disposal, and your sink and plumbing generally stay put. The resurfacing page covers the substrate requirements in detail.
New substrate fabrication. Where the existing top has failed, or the layout is changing, or you're building new, we prepare or fabricate a substrate built to your dimensions with cutouts and edges planned for the pour.
Both in one kitchen. A sound perimeter resurfaced in place, a new island substrate built for a changed layout, one design running across all of it. The finished surface reads as one thing regardless of what's underneath.
We determine the right approach per section during the on-site assessment, not from photographs alone.
Design possibilities
Doing the whole kitchen at once means the design decisions compound. Here's what's actually on the table.
Continuity or contrast. One design flowing across perimeter and island, or a quieter perimeter with the island carrying the drama. Doing both surfaces together is the only way to control that relationship deliberately. Done separately, it comes down to luck. See custom kitchen islands if the island is the only surface you're changing.
Custom color development. Base tone, accent colors, and veining are built against your actual cabinets and flooring rather than chosen from a catalog. This is the part slab selection can't offer at any price.
Seam placement. Long runs and corner conditions still involve seams, but on a poured surface they can be planned around your sightlines instead of dictated by slab dimensions.
Vertical detail. Waterfall returns and integrated backsplash treatment, where the structure and substrate support them. Feasibility gets confirmed on site.
Finish. From soft matte through higher sheen. Finish changes how the surface reads under your specific lighting more than most people expect, which is why samples get reviewed in your kitchen at the times of day you actually use it.
How the process works
- 01
Initial review
Send photographs of the full kitchen and rough measurements. We'll respond with a realistic planning range and a first read on whether you're looking at resurfacing, new substrates, or a combination.
- 02
On-site assessment
We inspect every section, the substrates, seams, edges, sink and cooktop conditions, backsplash transitions, and access. This is where the approach gets decided section by section.
- 03
Design and sample approval
We develop base color, movement, accents, and finish against the room, then create a physical sample. You review it in your kitchen, under your lighting, before anything is approved.
- 04
Preparation or fabrication
Sound substrates are cleaned, degreased, abraded, repaired, and primed in place. New substrates are fabricated to your layout with cutouts and edges planned. The room is masked and protected.
- 05
Pour and finish
The approved design is created by hand across every section. Seams, edges, sink openings, vertical returns, and backsplash transitions receive detailed finishing.
- 06
Cure and walkthrough
The surface and protective finish cure according to product requirements and the conditions in your home. We tell you when the kitchen can be used normally and review care before closing out.
What affects the schedule
A whole kitchen takes longer than a single surface, and it's worth knowing why before you plan around it.
- Number of separate sections and seams
- Whether sections are resurfaced in place or newly fabricated
- Substrate condition and repairs required
- Sink, cooktop, and cutout complexity
- Number of colors and veining layers
- Backsplash and vertical work
- Cure time and return visits
You'll have a written schedule before work begins, including when the kitchen is out of use and when it comes back. If the project depends on cabinet, plumbing, or electrical work by others, that sequence goes in the schedule rather than becoming a surprise.
Living with the surface
- Clean with mild soap and a soft cloth
- Never set a hot pan directly on the surface. Use trivets
- Use cutting boards rather than cutting on the counter
- Skip abrasive cleaners and aggressive scrubbing pads
- Call us about scratches or damage before attempting a repair yourself
Resin doesn't beat stone on every measure. Stone handles direct heat better and takes more abuse without marking. What resin gives you in return is a surface designed for your room specifically, and localized damage that can often be repaired or renewed in place rather than replacing a section.
What should I budget?
Most full kitchens: approximately $2,800 to $5,600
Highly detailed or multi-surface kitchens: $4,800 to $7,200+
New custom substrates: Individually quoted
Where your project lands depends on the number of sections, substrate condition, whether we're resurfacing or fabricating, cutouts and edge profiles, backsplash treatment, and the number of colors and veining layers.
Send photographs and rough measurements for an initial planning range. After the on-site assessment you'll receive a fixed proposal before you approve anything.
Frequently asked questions
Let's design a surface that belongs in your room.
Send photographs of the whole kitchen and we'll tell you what's possible, what needs to happen first, and what it's likely to cost.
FlowStone Countertops serves the Denver Metro area. View service areas